← Knowledge & insights

Robotics in business

How grippers and centres of gravity affect payloads

Why weight alone is not enough to select a robot, and how businesses can assess the tool, workpiece and movement together.

Nivama Robotics5 min read

A robot is to move metal parts from a pallet into a machine. The heaviest part weighs 16 kilograms, and the selected arm has a rated payload of 20 kilograms. That appears sufficient. Add a five-kilogram gripper, however, and the moving mass already reaches 21 kilograms. Tool changers and brackets have not yet been included. A simple addition is enough to rule out this selection.

This illustrative example shows the first step in sizing a robot: the payload includes everything attached to its tool mounting point. A complete assessment also needs to establish the combined centre of gravity. A long tool loads the wrist differently from a compact assembly of the same weight. Universal Robots explains this often overlooked relationship in a technical article dated 29 September 2026.

The number on the product page is therefore a starting point. Whether the robot can perform the intended task depends on the tool, the workpiece and the movement together. This matters particularly when two quotations specify the same payload but propose different grippers or installation arrangements.

Weight and distance belong together

The tool mounting face at the end of the robot arm is called the flange. The position of the attached components’ combined centre of gravity is measured relative to it. A load extending farther out creates a longer lever arm when the robot is oriented accordingly. A shopping bag illustrates the principle: it is easier to hold close to your body than at arm’s length.

For a simplified comparison, assume a four-kilogram gripper with its centre of gravity ten centimetres in front of the flange. A twelve-kilogram workpiece has its centre of gravity 30 centimetres in front of it. Together they weigh 16 kilograms. Their combined centre of gravity is 25 centimetres from the flange: multiply each mass by its distance, add the results and divide by the total mass.

This is a one-dimensional calculation, not a specification for a particular robot. A real application must account for positions in three dimensions and other load properties. Yet the essential point is clear: this arm must handle 16 kilograms with a centre-of-gravity offset of 250 millimetres. Checking that 16 is less than 20 does not establish whether it can do that.

Manufacturers provide payload diagrams for this purpose. These show the permitted combinations of mass and centre-of-gravity offset under the stated conditions. The UR30 manual, for example, explicitly refers to both gripper and workpiece and explains how load arrangement can affect acceleration. The relevant diagram is the one for the model being offered; another arm’s values cannot be substituted.

A lighter gripper is not automatically the better solution either. In our example, a shorter design might bring the centre of gravity closer to the flange. But it must still reach the workpiece and hold it reliably. If machine guarding obstructs access, the longer design may be necessary. The robot and its installation then need to accommodate that requirement.

What should be established before ordering

A useful enquiry therefore describes the complete tool assembly. It includes gripper mass, additional adapters and sensors, and the heaviest workpieces. For several part variants, a single weight is insufficient: a lighter, longer part may have a different centre of gravity from a heavier, compact one. Drawings or CAD models help make these differences explicit.

The next step is to consider the actual cycle. The arm picks up the workpiece, lifts it, moves towards the machine, rotates it if necessary and places it down. The required cycle time applies to this entire path. A quotation should therefore state the load, tool geometry and movement used to calculate or test the proposed cycle time. Otherwise, purchasing teams may be comparing different tasks under the same performance heading.

A second, purely illustrative calculation shows the economic connection. If a transfer cycle takes 24 seconds instead of the planned 20, theoretical output falls from 180 to 150 transfers per hour. That is approximately 17 percent less, before any other waiting time is included. These figures are an example, not a measured performance loss for a particular robot.

During commissioning, the controller’s load settings must also be correct. Universal Robots describes a wizard for estimating payload mass and centre of gravity. It uses several robot positions and identifies combinations that may reduce performance. This helps configure the system; it does not increase the arm’s mechanical capacity after installation.

The load changes between an empty and a loaded gripper. The program needs to account for these states appropriately. The manufacturer’s documentation on payload parameters specifically identifies picking up or putting down a workpiece as a reason to update them. Implementation must follow the commands and settings applicable to the installed controller version.

The selection process should end with a verifiable commitment: this arm can move this tool assembly and these parts along the intended path within the agreed time. That requires an agreed load model and a meaningful trial or suitable calculation. The kilogram rating remains important. Its practical value comes from the conditions under which the robot can actually use that capacity.

Sources checked: 12 November 2026. Technical information refers to the linked manufacturer documentation. All numerical examples are illustrative calculations created for this article.